• Oxygen banners 111
  • Oxygen banners 2222
  • Oxygen banners 33
  • Oxygen banners 444
  • Oxygen banners 55
  • Oxygen banners 66

Salter PRO2 Elite Oxygen Concentration Multifunction Indicator

Salter PRO2 Elite Oxygen Concentration Multifunction Indicator
  • Click to enlarge
Product Code
VAT relief available on this item

£470.75 Ex VAT

ABOUT Salter PRO2 Elite Oxygen Concentration Multifunction Indicator
  • Description

    Salter PRO2 Elite Oxygen Concentration Multifunction Indicator


    • FLOW LPM 


    With microprocessor logic and ultrasound technology there is no need to carry a tool box full of test equipment to measure concentrator performance or spot check LOX systems. One simple tubing connection and you are ready to go! It comes complete with a carrying case and a 9-volt battery pre-installed.

    All in One - a small hand held unit which delivers all three (3) essential validation checks required to assure proper oxygen concentrator performance.

    • Oxygen percent of delivered gas

    • Output pressure in PSIG or kPa

    • Output flow rate in LPM

    Minimal Maintenance costs…

    • DC powered with a single standard 9-volt battery and a low battery warning display

    • NO FUEL CELL to replace . . . ever

    • Automatic power shutoff after five minutes prolongs battery life

    • No special tools required to replace battery and the battery is included!

    No Calibration required …

    • Microprocessor factory set electronic calibration

    • If calibration or verification is required to meet company or local standards, it can be performed on site in   minutes with no special equipment

    PRO2 Check Elite® A Multifunction Oxygen Concentration Indicator
    This lightweight hand held device is a welcome addition for care providers or repair technicians working with oxygen concentrators. In one small, compact battery operated instrument you have the ability to readily check three vital parameters of a concentrator’s function . . . OXYGEN PERCENTAGE delivered, FLOW RATE LPM, PRESSURE PSIG or kPa*. In the past, these value checks would require three (3) separate instruments plus the time to connect all three instruments to check each parameter separately. Each test instrument requires some defined calibration or test procedure and each with its own adapter/connector to collect data. Additionally if you are using an oxygen analyzer, which incorporates a galvanic fuel cell, you may be replacing the fuel cell on a regular basis. Typically this style analyzer will also require regular recalibrations and may be sensitive to temperature or elevation changes all of which require dedicated time to perform.

    The PRO2 Check Elite® is a microprocessor driven device with logic designed to simply and accurately indicate delivery flow in LPM; pressure, in PSIG or kPa, as well as oxygen percentage WITHOUT the need for repeated calibrations. Oxygen analysis is performed using ultrasound, the same technology many concentrator manufacturers incorporate into their units. It is not affected by normal temperature or elevation changes and by using the microprocessor logic can be recalibrated in minutes with two buttons and a USP 99.9% oxygen source. A verification check can be done in 10 seconds with one button. There is no need for additional special test equipment. There is no fuel cell to replace. It operates on a standard 9-volt battery and automatically shuts off after (5) five minutes, plus utilizes a LCD liquid crystal display to prolong battery life. When a battery is reaching the end of usefulness a “LO BATT” read out will appear in the display window. No tools are required to replace the battery; simply slide the cover off exchange batteries and you are ready. Annual operational costs are one or possibly two 9-volt batteries, depending on usage.

    It comes in a carrying case with a clear plastic face to protect the unit from spills. The switches are a new membrane style, which are a low profile design with no sharp edges to get caught or inadvertently triggered. The case also has a handy belt clip to attach to your belt or lab coat pocket and an adjustable carrying strap if you prefer putting it over-the-shoulder. The battery comes pre-installed and the PRO2 Check Elite® is ready to go right out of the box! The PROCheck Elite® has a 2-year warranty.

    Physical data  Battery  
    Dimensions: 3.60” W x 5.75” H x 1.29” D (9.14 cm W x 14.61 cm H x 3.28 cm D)  Standard 9-volt  
    Weight: 9 ounces (255.15 grams)  Operating Temperature  
    Connector: (2) 1/4” anodized aluminum hose barbs  32º F to 105º F (0º C to 41º C)  
    Case: Solid color ABS plastic with threaded metal bolt channels  Storage Temperature  
     Specifications: Pressure Mode   -29º F to 160º F (-34º C to 71º C)  
     Range: 0 to 25 PSIG (0 to 172 kPa)   Specifications: Concentration Mode  
     Resolution: 0.1 PSIG (0.1 up to 99.9 kPa; 1.0 over 100 kPa)   Range: 20.9% to 100%  
     Accuracy: ± 1% of Full Scale   Response time: 10 seconds  
     Specifications: Flow Mode   Accuracy: ± 2%  
     Range: 0 to 10 LPM   Linearity: ± 2% Full Scale  
     Resolution: 0.1 LPM   
     Accuracy: ± .3 LPM   
     Sensor: Ultrasonic  



Customer Reviews

This product hasn't been reviewed yet.

Write a review

Write Review

Please enter a valid email address.
This field is required.

  • 756 large default
  • airsep
  • BM logo2
  • BPR
  • caire logo 2x
  • devilbiss
  • gce logo.gif
  • inogen
  • intersurgical
  • invacare
  • kroeber
  • Kuuse
  • nidek
  • nonin
  • Oxylitre
  • philips
  • reflex logo gb flag
  • salter labs
  • sequal
  • southmedic

© Copyright Bar O2 Limited T/A the OxygenStore 2001-2022.  All rights reserved.  Company Registered in UK No 04192727.  VAT Registration No 770 4717 24. EORI GB770471724000 EORI XI770471724000  Dun and Bradstreet D-U-N-s No 232439047